How To Install A Shower Surround Over Existing Tiles

Installing a shower surround over existing tiles is a relatively easy task that can be completed in a few hours. The first step is to remove any existing caulk or sealant from around the perimeter of the shower. Next, apply a bead of silicone caulk to the back of the shower surround and place it over the existing tiles. Use a level to make sure the surround is level and then use silicone caulk to seal the joints between the surround and the tiles.

7 Steps to Install A Shower Surround Over Existing Tiles

Installing a shower surround over existing tiles is a relatively easy process. First, remove any molding or trim around the perimeter of the shower. Next, use a utility knife to score the caulk or grout around the outside of the shower. Be sure to score all four sides. Finally, use a putty knife to pry the surround away from the tiles. If the surround is held in place with screws, remove them with a drill.

One of the most important skills that a homeowner can learn is how to install a shower surround over existing tiles. This project can be very challenging and if not done correctly, can result in a very costly repair bill. By learning how to install a shower surround over existing tiles, homeowners can save themselves a lot of money and frustration.

Step 1: Remove The Old Shower Surround

Remove the old shower surround by unscrewing the screws or nails holding it in place. Carefully pull the surround away from the wall, taking care not to damage the wall or surrounding tiles.

Step 2: Clean The Surface Of The Tiles

If you are planning to install a shower surround over existing tiles, make sure to clean the surface of the tiles first. This will help ensure that the new surround adheres properly and looks its best. Start by scrubbing the tiles with a mild detergent and a soft brush. If there are any stubborn stains, you may need to use a harsher cleaning solution. Once the tiles are clean, rinse them thoroughly with water and allow them to dry completely before proceeding.

Step 3: Measure And Cut The New Shower Surround To Size

To install a new shower surround over existing tiles, measure and cut the new surround to size. Cut any necessary holes for fixtures, then attach the surround to the wall using screws or adhesive.

Step 4: Apply Adhesive To The Back Of The Shower Surround

To install a shower surround over existing tiles, first apply adhesive to the back of the shower surround. Next, place the surround in the desired position and use a level to ensure it is level. Finally, use screws or nails to secure the surround in place.

Step 5: Stick The Shower Surround To The Tiles

1. Remove the old shower surround. 2. Stick the new shower surround to the tiles with silicone caulk or a similar adhesive. 3. Use a level to make sure the new surround is straight, then caulk or adhesive around the outside edge to secure it in place. 4. Let the caulk or adhesive dry completely before using the shower.

Step 6: Wait For The Adhesive To Dry

If you are installing a shower surround over existing tiles, you will need to wait for the adhesive to dry before proceeding. This step is important in order to ensure a secure and watertight seal. Once the adhesive has dried, you can then move on to the next step in the installation process.

Step 7: Attach The Shower Door And/Or Frame

Attach the shower door and/or frame to the new surround. Make sure the door or frame is properly sealed to avoid leaks.

Frequently Asked Questions

How Do You Replace A Tile Shower Surround?

You can replace a tile shower surround by removing the old tiles and installing new ones.

How Much Does It Cost To Replace A Tile Shower Surround?

It can cost anywhere from $200 to $2,000 to replace a tile shower surround. The cost will depend on the size of the shower, the type of tile, and the labor involved.

In Closing

To install a shower surround over existing tiles, use a level to mark where the new surround will go and use a drill and a hammer to remove the tiles in that area. Clean the surface and then apply construction adhesive to the back of the surround and press it into place. Install screws through the surround into the wall studs and then apply sealant around the edge.