How To Pull A Well Pump

A well pump is a pump that is used to draw water from a well. The most common type of well pump is a submersible pump, which is a type of pump that is submerged in the water. Other types of well pumps include jet pumps and hand pumps.

8 Steps to Pull A Well Pump

How to Pull a Well Pump 1. identify the problem 2. shut off the power 3. disconnect the pump from the well 4. remove the pump from the well 5. repair or replace the pump 6. reassemble the pump 7. reconnect the pump to the well 8. turn on the power 9. test the pump

In many rural areas, water is supplied by a well. If the power goes out, or the water pump fails, then the only way to get water is to manually pump it from the well. Learning how to do this is important for anyone who lives in a rural area, or who may find themselves in a situation where they need to get water from a well.

Step 1: How To Pull A Well Pump

In order to pull a well pump, the first step is to locate the well. Once the well is located, the next step is to determine the depth of the well. The third step is to find the right equipment for the job. The fourth step is to attach the equipment to the well. The fifth step is to start the pump. The sixth step is to monitor the progress of the pump. The seventh step is to remove the pump from the well.

Step 2: Get The Right Tools

In order to pull a well pump, you will need a few tools. A length of pipe, a well cap, a sledgehammer, and a come-along or hand winch will be necessary. You will also need some rope or cable to attach the pump to the come-along. With these tools, you should be able to remove the well pump from the well.

Step 3: Find The Well Cover

The first step is to find the well cover. The well cover is typically a metal or plastic lid that is placed over the top of the well. There may be a handle on the well cover that can be used to lift it off of the well. If there is no handle, the well cover can be pried off with a screwdriver or other tool.

Step 4: Release The Clamp

The release the clamp step of pulling a well pump is when you remove the clamp that is holding the well pump in place. This step is important because it allows you to remove the well pump without damaging it.

Step 5: Remove The Cover

Remove the cover from the wellhead. Doing this will give you access to the pipes and fittings that need to be removed in order to pull the well pump.

Step 6: Disconnect The Pump Cable

This step is important because if the pump is not properly disconnected, it could cause serious damage to the equipment. Make sure to follow the manufacturer’s instructions when disconnecting the pump.

Step 7: Lift The Pump Out Of The Well

Lift the pump out of the well. If your well has a submersible pump, you will need to hire a professional to do this step for you.

Step 8: Put The Pump Back In The Well Connect The Pump Cable Close The Well Cover Replace The Clamp

Put the pump back in the well: 1. Carefully lower the pump into the well. 2. Attach the pump cable to the pulley. 3. Close the well cover. 4. Replace the clamp.


Frequently Asked Questions

Can You Pull A Well Pump By Hand?

Most well pumps cannot be pulled by hand.

How Do You Pull A Submersible Pump Out Of A Well?

It is typically accomplished by using a well service rig to lower a work string and pull tool down the wellbore to the submersible pump. The work string has a series of hooks or lifts which engage theFishtail guide shoes or other engagement device on the submersible pump. The Fishtail guide shoes or other engagement device on the submersible pump.

How Much Does It Cost To Pull A Pump Out Of A Well?

It typically costs around $1,000 to pull a pump out of a well. However, this cost can vary depending on the size and depth of the well, as well as the company you hire.

In Summary

A well pump can be pulled by using a rope and attaching it to the pump handle. The other end of the rope is attached to a vehicle or other heavy object. The vehicle is then driven forward, pulling the pump out of the well.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *